NAME:WiFi LED Controller

I. Product Summarize

1,Product summarize

WiFi-LED controller is following the traditional with infrared, RF technology controller foundation, it is birth of market and customer's demand, it is one type controller which integration the newest wifi technical in the market. It makes the LED control more convenience, more hommization. We can use an Android system or IOS system mobile phone to install control software, then it can control LED, this is the wishes of every customer. Use WiFi technology can make our control range more wider, can get rid of narrow space constraint, in building can control more than 50m, in outdoor can control more than 100m. In the condition of not use the mobile software, also can use the remote control to control, very convenience, two choices for you.

2,Product constitute

------Product constitute of WiFi LED Controller

II. Technical Parameters

1.Remote control technical parameters

1:Working temperature:-20-60℃

2:Power supply method:AAA*3

3:Supply voltage:1.5V*3

4:Standby power:0.015mW

5:Standby current:3uA

6:Working current:200uA

7:Emission current:10mA

8:Remote control distance:about 50m

9:Standby time:6 months

2.Software technical parameters

1:Name:Magic Color 1.0

2:Runtime platform:Android version support Android system, IOS version support IOS system, equipment must have WiFi function.

3:Byte: Android version(622K),IOS version(581K).

4:Language: English

5:Category: communications

6:Free, green, no plug-ins

3.Controller technical parameters

1:Working voltage: DC5--24V

2:Output control: can flexible control 3 channel, 2 channel, 1 channel LED lamps.

3:Output current: 4A*3

4:Connect mode: common anode

5:Packing size:L215*W165*H55(mm)

6:External dimension: L107*W65*H30(mm)

7:Net weight:340g

8:Gross weight:480g

9:Receiving sensitivity: 802.11b DSSS(-5dBm),802.11b CCK (-10dBm),802.11g

OFDM(-15dBm)

III. Magic Color 1.0 Instruction

1.Magic Color 1.0 install course

1) This software have Android version and IOS version, according to your mobile phone to choose to install, below respectively introduce Android version and IOS version install and use method: Android version install as below:

Open the optical disk can see the Magic Color 1.0 erection Sequence ClickMagic Color 1.0.apk to install.Installation complete clickOpen application

1. On Off key 2.color disk 3.mode key 4.speed/brightness bar

5. RGB mode LED control page

6. Cold white and warm white mode LED control page

7. Dimmer mode LED control brightness page

8. Magic Color 1.0 software setting page

Following is control color temperature and brightness two mode page:

1. IOS version install method:(not escape or escape all can suit) can enter "app store"(if do not have iTunes,

please to download the iTunes client-side to install and registration first) search Magic Color 1.0.

Then it can find our software (below scheme just limit after escape) or open itunes,make our installation packageDragged into itunes,as pictureclick to install.Installation complete click,open application(same with Android version).

2. Connect WiFi network

If you open Magic Color 1.0 show like below picture: prompt to choose "OK", jump to WiFi setting interface connect WiFi LED controller. Or choose "cancel" don't jump, then setting SIMULATION is ON, it will change to do not connect controller node, diagram form as below:

choose proceed wifi setting window,Finished setting, if popup below window: indicate connect succeedopen wifi connect setting, prompt connect correct wifi equipment.

3. ON/OFF Key

ON/OFF, before control LED, open on/off key. Click OFF close LED equipment.

4. Mode Key Function

Mode key under 3 mode pages is entirely different, under CD mode page to control LED dynamic work mode, under CT mode page to control some kinds of special color temperature state, under DIM mode page to control some kinds of special brightness state.

5. Color disk instruction

Color disk under 3 mode page, the function is entirely different: under CD mode page is used for adjusting color, under CT mode page is used for adjusting color temperature, under DIM mode page is used for adjusting brightness.

6. CD mode page control function

CD mode page is used for controlling LED product which consist of red, green, blue, under this mode page, every time after touch the mode key "M", the lighten way will   change. "M" is used for setting LED dynamic effect. Color disk touch point change will make the LED color changed.

7. CT mode page control function

CT mode page is used for controlling LED product which consist of warm white and cold white. Brightness bar is used for setting the LED brightness, color disk adjusting LED color temperature, mode key is used for choosing some kinds of default special color temperature value.

8. DIM mode page control function

DIM mode page is used for controlling LED product which consist of single color, color disk is used for adjusting LED brightness, mode key "M" is switch some special brightness state(for example: 25% brightness, 50% brightness, 75% brightness, 100% brightness)

9. Speed/brightness bar instruction

Speed/brightness bar under different mode page is different: under CD mode page, different situation separately control brightness and speed, under CT mode page, it is control brightness.

10. Setup mode function

The last is Setup touch key, it have SIMULATION ,SOUND and WiFi CONNECTION 3 options,

SIMULATION is mainly used for setting software imitate and actually connect LED-WiFi controller to choose, if choose ON state, do not need to connect LED-WiFi controller, it can used for software demonstrate, imitate demonstrate ect. Practical application need to set OFF (actually, when you connect WiFi, the software have automatic set to OFF), SOUND is the prompt tone of click the software switch, WiFi CONNECTION is used for jumping to wifi network setting interface proceed wifi connection.

IV. LED-WiFi Controller Function Instruction

1.Working state instruction

2.Setting SSID number

The dial code is used for setting WiFi-LED controller Ssid number corresponding table as below. Form 0 to F, have 16 code in total, so our Ssid number fasten to LN001 to LN016.

That means use our product in same small area can set 16 mutual isolation LAN, once the dial code changed after switch was dialed, Ssid number immediately be modified, so you need to note that it need to search and connect again.

3.Connect LED, Power supply port

LED port under CD mode page need to connect RGB 3 channel LED equipment, under CT mode page need to connect cold white and warm white 2 channel LED equipment group, under DIM mode page need to connect single color LED equipment.

4. Match Key function

The first time use the controller and remote control, maybe because the controller address and remote control address is not match, it will cause the remote control can not control, at this time, it need to use this button to make this 2 address matched.

Use method: first, press the controller "Match" key, at the same time press any key of the remote control, more than 2s, release "Match" key, then finished.

5. Function key function

"Function" key is a composite button, it has switch and mode change function.

Function instruction: long-time(more than 2s): on off;

Short press(less than 1s): mode change.

6. Remote control function instruction

------Remote control function instruction of WiFi LED Controller

1,on/off key 2,pause key 3,mode+ 4,mode-

5,Color pulley key 6,brightness+ 7,brightness-

8,speed+ 9,speed

1﹑Touch remote panel have 64 touch button(point), each button function as below:

1,on/off key, any state, can turn on or turn off controller output;

2,pause key, under dynamic mode, can make the controller stop current state;

3,this key have 2 functions:

①mode add key, so when the current control mode is pulley mode (color), if it need to realize the mode (color) in controller, can press this button.

②mode switch key, so when the current control mode is M key mode, can switch the

regulation mode (color) in M+ key mode table.

4,This key have 2 functions:

①mode minus key, so when the current control mode is pulley mode (color), if it need

to realize the mode(color) in controller, can press this button.

②mode switch key, so when the current control mode is M key mode, can switch the

regulation mode(color) in M- key mode table.

5,output brightness control key, every time you press this button, the brightness

series add 1, altogether 100 levels;

6,output brightness control key, every time you press this button, the brightness

series minus 1, altogether 100 levels;

7,output speed control key, every time you press this button, the speed series add

1, altogether 100 levels;

8,output speed control key, every time you press this button, the speed series

minus 1, altogether 100 levels;

9,Color pulley touch button, static mode choose key, up to 55 touch point. This key have 2 functions:

①pulley static color choose button, so when the current control mode is M key

Mode (color), if need to realize the static color on pulley, can press this button.

②pulley color switch key: can switch from 55 static color(pulley shows color).

2,Power management: Stop using remote control more than 20 s, remote control will automatically into standby mode(the state can not touch),to extend the battery life for use; shake the remote mildly remote return to work station(the state can touch). Remark: This remoter just apply to RGB model.

7. Built-in mode form of controller

1The mode form of RGB Control:

1,The mode form of color temperature control:

2,The mode form of dimming Control:

V. Explain installed hardware

1. Install ANT

ANT's installation drawing: 

------The installation of WiFi LED Controller

clockwise install WIFI antenna and anticlockwise take down the antenna.

2. Install power supply and LED equipment

This connector structure belong to drawer structure, the device interface of power supply and LED is together, four interface one the left side (3,2,1,V+)is connect led equipment, the fifth interface is connect the anode V+ of power supply, the sixth interface is connect the cathode V- of power supply. According to the rated voltage of led lamp, we supply power to controller ,and the rated voltage of controller is 24V. As follows:

------Install power supply and LED equipment of WiFi LED Controller

2.Connect three channels LED instruction

------Connect three channels LED instruction of WiFi LED Controller

When connect three channels LED, you should put the Magic Color 1.0 software switch to CD mode to use, only under this mode, you can control the LED's color, brightness and speed. Color disk adjust the color (Adjust process can be seen in the upper left corner R, G, B numerical with change), speed/brightness item adjust speed and bright("M" set the LED dynamic effect, "M"adjust the LED dynamic change.

3. Connect two channels LED instruction

------Connect two channels LED instruction of WiFi LED Controller

4.Connect one channel LED instruction

------Connect one channels LED instruction of WiFi LED Controller

When connect three channels LED, you should put the Magic Color 1.0 software switch to DIM mode to use, under this mode, use color disk control the LED's brightness, Adjust process can be seen in the upper left corner NM numerical with change.

VI. FAQ

1. Magic Color 1.0 can not open(error and breakdown),how to do?

Answer:

If it is happened, just need to open again then you can solve. If it is still not open, that maybe the compatibility of software to this phone is not very good, so you need to install the software to other phone to use.

2. Magic Color 1.0 can not control LED?

Answer:

It maybe happen of wifi connection unsteadily.

1, you can try shorten the distance of phone and controller.

2, you can enter SETUP reconnection (reinstall simulation to OFF),

Answer:

It maybe happen of wifi connection unsteadily.

1, you can try shorten the distance of phone and controller.

2, you can enter SETUP reconnection (reinstall simulation to OFF),

if appear this ,if the network of you connect is LN0XX form, that is maybe phone and wifi connection unsteadily, so retry several times, if it is still not useful, so you need to change the phone.

3, close the software and open again. One of above three ways can solve this problem, but if there can not get the data ,you must be ensure the distance is not too far.